Installing a bottleless water cooler is a straightforward process that involves connecting the unit to a water supply and power source. This comprehensive guide will walk you through the step-by-step installation process, providing detailed instructions and technical specifications to ensure a successful and efficient setup.
Choosing the Ideal Location
The first step in installing a bottleless water cooler is to select the perfect location. Ideally, the unit should be placed between a water line and a grounded wall outlet, ensuring easy access to both the water supply and power source. The water dispenser should be positioned on a leveled, hard surface, such as a countertop or a sturdy table, to provide stability and prevent any potential spills or leaks.
When choosing the location, it’s crucial to consider the dimensions of the bottleless water cooler. Measure the available space to ensure the unit will fit comfortably without obstructing any nearby cabinets, appliances, or foot traffic. Refer to the manufacturer’s specifications for the exact dimensions of the model you’ve selected.
Disconnecting the Current Cold Water Supply
Before you can install the bottleless water cooler, you’ll need to disconnect the current cold water supply. This process typically involves the following steps:
-
Locate the Cold Water Supply Line: Identify the cold water supply line that will be used to feed the bottleless water cooler. This line is usually located under the sink or near the intended installation area.
-
Turn Off the Water Supply: Locate the shut-off valve for the cold water supply line and turn it clockwise to shut off the water flow.
-
Disconnect the Cold Water Line: Using a wrench, disconnect the cold water line from the supply. Be prepared for a small amount of water to drain out during this process.
-
Install the Feed Water Adapter: Once the cold water line is disconnected, install the included T-shaped Feed Water Adapter. Connect the cold water supply to the top of the adapter and the water dispensing line to the quick connecting piece.
Ensuring Secure Connections
After installing the Feed Water Adapter, it’s crucial to ensure that all connections are secure and leak-free. Gently tug on the water lines to verify that they are firmly attached to the adapter and the bottleless water cooler.
If you encounter any leaks or loose connections, tighten the fittings using a wrench or pliers. Avoid over-tightening, as this can damage the components and lead to further issues.
Turning On the Water and Unit
With the connections in place, it’s time to turn on the water supply and the bottleless water cooler. Follow these steps:
-
Turn On the Water Supply: Slowly turn the shut-off valve counterclockwise to restore the water flow to the cold water line.
-
Turn On the Bottleless Water Cooler: Plug the power cord of the bottleless water cooler into the grounded wall outlet and turn on the unit.
-
Allow the System to Fill: The water dispenser will begin to pump water through the filtration system and store the clean water in the stainless steel reservoirs. This process may take several minutes, depending on the size of the reservoirs and the water flow rate.
Installing a Reverse Osmosis Filtration System
Many bottleless water coolers utilize a reverse osmosis (RO) filtration system to provide clean, purified water. If your bottleless water cooler includes an RO system, the installation process will involve additional steps:
-
Gather Necessary Tools: Ensure you have all the required tools, such as a drill, a hole saw, pliers, and a wrench, to complete the RO system installation.
-
Connect the Cold Water Supply: Locate the cold water supply line and connect it to the RO system’s inlet.
-
Insert the Shut-Off Valve Tube: Install the shut-off valve tube, which will allow you to turn off the water supply to the RO system for maintenance or filter replacements.
-
Locate the Drain Line: Identify the drain line, typically located underneath the sink or in another convenient location.
-
Place the Drain Saddle: Ensure that the drain saddle is placed on the P-trap or on a straight vertical/horizontal section of the drain line.
-
Drill a Hole: Using a drill and a hole saw, create a hole on one side of the drain line to accommodate the wastewater line from the RO system.
-
Mount the Drain Saddle: Align the holes and securely mount the drain saddle on the drain line.
-
Tighten the Saddle: Tighten the saddle on the drain line and connect the wastewater line from the RO system.
-
Flush and Install the Filters: Follow the manufacturer’s instructions to flush the RO system and install the necessary filters.
-
Plug In the Water Cooler: Finally, plug in the bottleless water cooler, flip the cooling and heating switches to the “on” position, and start dispensing clean, filtered water.
Remember, the installation process may vary depending on the specific model and brand of the bottleless water cooler. Always refer to the user manual or installation guide provided by the manufacturer for detailed, model-specific instructions.
Conclusion
Installing a bottleless water cooler is a straightforward process that can be easily accomplished with the right tools and a bit of patience. By following the step-by-step instructions outlined in this comprehensive guide, you can ensure a successful and efficient installation, providing your home or office with a reliable source of clean, filtered water.
If you encounter any issues or have additional questions, don’t hesitate to consult the manufacturer’s support resources or seek the assistance of a professional plumber or technician.
References:
– How to Install a Bottleless Cooler
– Bottleless Installation How-To Videos
– Installing Your Bottleless Water Cooler