Setting up a Culligan water cooler involves several intricate steps, including preparing the dispenser for bottled water, initial setup for a bottled water system, adjusting the siphon tube for smaller bottles, preparing the water dispenser for use as a bottle-less system, adding filtration, and initial set-up for a bottle-less system. This comprehensive guide will walk you through each step in meticulous detail, ensuring a seamless installation process.
Preparing the Dispenser for Bottled Water
-
Placing the Water Bottle: Start by placing the water bottle on the floor in front of the dispenser. Ensure that the bottle is positioned directly in front of the dispenser’s water intake tube.
-
Removing the Plastic Cap: Carefully remove the plastic cap from the mouth of the water bottle. This will allow the water to flow freely into the dispenser.
-
Inserting the Tube: Gently push the water intake tube through the collet ring and into the body of the dispenser. Make sure that the tube sits fully past the o-ring, creating a secure and leak-proof connection.
-
Disconnecting the Tube: If you need to disconnect the tube, simply hold the collet ring against the body of the dispenser and pull the tube out.
-
Pressure Regulation: If the inlet water pressure is greater than 100 psi, you must install a pressure regulator prior to the water dispenser connection. This will ensure the proper water pressure for the system.
Initial Setup for a Bottled Water System
-
Connecting the Tubes: Connect the white tube to the filter system inlet and the blue tube to the filter system outlet. This will ensure the water is properly filtered before entering the dispenser.
-
Inserting the Filtered Water Line: Insert the filtered water out line into the Water Line In bulkhead fitting on the back of the unit. This will complete the connection between the filter system and the dispenser.
-
Internal Filter Installation: If you are installing an internal filter, locate the coil of tubing inside the cabinet on the left side. Disconnect and remove the push fit union fitting, then use the tube ends to connect to the filter.
Adjusting the Siphon Tube for Smaller Bottles
-
Identifying the Siphon Tube: Locate the siphon tube, which is the clear plastic tube that extends from the water intake tube into the water bottle.
-
Trimming the Siphon Tube: If you are using a smaller water bottle, you may need to trim the siphon tube to ensure it reaches the bottom of the bottle. Carefully measure and cut the tube to the appropriate length.
-
Reinstalling the Siphon Tube: After trimming, reinsert the siphon tube into the water intake tube, making sure it is securely in place.
Preparing the Water Dispenser for a Bottle-less System
-
Connecting to a Direct Water Line: For a bottle-less system, the water dispenser must be connected to a direct water line. This will provide a continuous water supply without the need for a water bottle.
-
Connecting the Tubes: Connect the white tube to the filter system inlet and the blue tube to the filter system outlet. This will ensure the water is properly filtered before entering the dispenser.
-
Inserting the Filtered Water Line: Insert the filtered water out line into the Water Line In bulkhead fitting on the back of the unit. This will complete the connection between the filter system and the dispenser.
Adding Filtration
-
Connecting the Filter System: Connect the white tube to the filter system inlet and the blue tube to the filter system outlet. This will ensure the water is properly filtered before entering the dispenser.
-
Flushing the Filters: Before installing the filters, make sure to flush them as per the manufacturer’s recommendations. This will remove any impurities or debris that may have accumulated during storage or shipping.
-
Connecting the Filtered Water Line: Insert the filtered water out line into the Water Line In bulkhead fitting on the back of the unit. This will complete the connection between the filter system and the dispenser.
Initial Set-up for a Bottle-less System
-
Connecting to a Direct Water Line: For a bottle-less system, the water dispenser must be connected to a direct water line. This will provide a continuous water supply without the need for a water bottle.
-
Connecting the Tubes: Connect the white tube to the filter system inlet and the blue tube to the filter system outlet. This will ensure the water is properly filtered before entering the dispenser.
-
Inserting the Filtered Water Line: Insert the filtered water out line into the Water Line In bulkhead fitting on the back of the unit. This will complete the connection between the filter system and the dispenser.
-
Pressure Regulation: If the inlet water pressure is greater than 100 psi, you must install a pressure regulator prior to the water dispenser connection. This will ensure the proper water pressure for the system.
By following these detailed steps, you can successfully set up your Culligan water cooler, whether you choose a bottled water system or a bottle-less system. Remember to always refer to the manufacturer’s instructions and safety guidelines for the most up-to-date and accurate information.
Technical Specifications
The Culligan Bottom Load/Tri-Temp Direct Connect Convertible Water Cooler has the following technical specifications:
- Dimensions: 38.6 cm x 35.8 cm x 12 cm (15.2 in. x 14.17 in. x 47.24 in.)
- Weight: 19.75 kg (36.60 lb.)
- Design: Bottom-loading
- Water Temperatures: Tri-temp providing hot, cold, and room temperature water
- Cooling Capacity: Commercial-grade
- Sanitization: LED UV tank for superior self-sanitization
- Dispensing Area: 27.9 cm (11 in.)
- Certifications: UL listed, ENERGY STAR® certified
- Finish: Smudge-resistant stainless-steel